Follow the steps to set 3D Emboss Engraving of EZCAD3: 1. Enter 3D view, click “STL” to import a 3D file, or we can click “Creating a basic 3D surface” to create a basic 3D file. 2. We can view it from different directions. 3. Slice the 3D file. 4. Click “Add contour”, then click… How to set 3D Emboss Engraving of EZCAD3? weiterlesen
FAQs: Probleme und Lösungen bei der Lasergravur
Beim Lasergravieren oder -markieren kommt es zwangsläufig zu peinlichen Zwischenfällen. In diesem Katalog haben wir eine Sammlung häufiger Probleme beim Lasergravieren und Lösungsvorschläge zusammengestellt.
Hierzu zählen unter anderem:
- Probleme mit der Installation, den Anschlüssen, der Haupteinheit oder der Stromversorgung der Lasermaschine.
- Fragen zur Lasermarkierungssoftware, beispielsweise Bedienung, Funktionen, Parameter, Gravurdateiformate und andere Unklarheiten.
- Bedenken hinsichtlich der Auswahl des Gravurmaterials.
Wir hoffen, dass diese Ressourcen Ihnen dabei helfen, alle Probleme, die bei der Arbeit mit Lasermaschinen. Wenn nicht, können Sie sich jederzeit an uns wenden, wir helfen Ihnen gerne weiter!
How to set 2D Emboss Engraving of EZCAD3?
Follow the steps to set 2D Emboss Engraving of EZCAD3: 1. Create a new TEXT 2D file or import a vector file to Ezcad3, set its size and put it to center. 2. Click “3D” to enter 3D view, click “Slice” to slice the file, remember to tick “Using selected two-dimension object hierarchy”, set the… How to set 2D Emboss Engraving of EZCAD3? weiterlesen
How to Adjust the Power of an Inno UV Laser Source?
The product of pulse width and frequency is approximately 1,000 (the actual value is around 960). For example, at 50 kHz, the maximum power corresponds to a pulse width of 19, while the minimum power corresponds to a pulse width of 1. Inno Laser sources have a frequency range of 30–150 kHz. However, to make… How to Adjust the Power of an Inno UV Laser Source? weiterlesen
How do I reset the dimensions of the marking area frame in EZCAD2?
System parameter -> WorkSpace Left bottom corner: The X and Y values are both set to half of the field lens’s working range (e.g., 55, 55). Size: Set the Width and Height to the values of the field lens‘s working range (e.g., 110, 110).
How to Use a Linxuan UV Laser Marking Machine with a Water Chiller? A Step-by-Step Guide
This article primarily covers the operating procedures and precautions for the Linxuan UV laser marking machine and its associated water chiller. Water Chiller Installation 1. Add purified water to the chiller, and the water level over the part that marked in picture. 2. There are two lines, one connect power supply, another connect to the… How to Use a Linxuan UV Laser Marking Machine with a Water Chiller? A Step-by-Step Guide weiterlesen
How to take off the control card of Linxuan laser engraver?
1. Take off the cabinet case with rotating the 10 screws on two sides. 2. Then you will see the control card on a metal sheet. Take off it with the two screws. And take of the plug on the card. Please be careful when do it. 3. Then take off the card.
How to take off the laser head of Linxuan laser engraver?
1. First, take off the lens with rotating the bottom piece in red circle. Please note not rotate the whole black part. But only rotate the bottom. Please hold the lens by another hand when rotating. So that it will not fall on the ground. Please take care of the lens to put it in… How to take off the laser head of Linxuan laser engraver? weiterlesen
How to replace the aiming diode of Linxuan laser engraver?
1. Loosen these three screws. 2. Pull the aiming diode out and loosen the connector of the bad aiming diode, tight this good aiming diode’s male connector with another female connector which inside of the scanner head. 3. Put the laser head at right focal distance, move this aiming diode and let two aiming diode’s… How to replace the aiming diode of Linxuan laser engraver? weiterlesen
How to Laser Print the Date and Time Automatically by EZCAD2?
With Linxuan laser engraver and the software EZCAD2, you can mark the date and time automatically. Here are the steps: 1. Click “Draw Text” tool, and choose “Enable variable Text”, then “Add” the “Date”, you can choose “Year-2020” or “Year-20” as you like to use, then click “OK” to add the year. 2. “Add”->”Date”->choose “Month”, then click “ok” to add the… How to Laser Print the Date and Time Automatically by EZCAD2? weiterlesen
