This article primarily covers the operating procedures and precautions for the Linxuan UV laser marking machine and its associated water chiller. Water Chiller Installation 1. Add purified water to the chiller, and the water level over the part that marked in picture. 2. There are two lines, one connect power supply, another connect to the… Seguir leyendo How to Use a Linxuan UV Laser Marking Machine with a Water Chiller? A Step-by-Step Guide
Preguntas frecuentes: problemas y soluciones del grabado láser
Durante el proceso de grabado o marcado láser, es inevitable encontrarse con algunos inconvenientes embarazosos. En este catálogo, hemos recopilado una colección de problemas comunes relacionados con el grabado láser y sugerencias para solucionarlos.
Incluyen, entre otros:
- Problemas con la instalación de máquinas láser, conexiones, unidad principal o fuente de alimentación.
- Preguntas sobre el software de marcado láser, como funcionamiento, funciones, parámetros, formatos de archivos de grabado y otras dudas.
- Preocupaciones sobre la selección de materiales de grabado.
Esperamos que estos recursos le ayuden a resolver rápidamente cualquier problema que enfrente mientras trabaja con máquinas láserSi no es así, no dude en ponerse en contacto con nosotros para obtener ayuda. ¡Estaremos encantados de ayudarle!
How to take off the control card of Linxuan laser engraver?
1. Take off the cabinet case with rotating the 10 screws on two sides. 2. Then you will see the control card on a metal sheet. Take off it with the two screws. And take of the plug on the card. Please be careful when do it. 3. Then take off the card.
How to take off the laser head of Linxuan laser engraver?
1. First, take off the lens with rotating the bottom piece in red circle. Please note not rotate the whole black part. But only rotate the bottom. Please hold the lens by another hand when rotating. So that it will not fall on the ground. Please take care of the lens to put it in… Seguir leyendo How to take off the laser head of Linxuan laser engraver?
How to replace the aiming diode of Linxuan laser engraver?
1. Loosen these three screws. 2. Pull the aiming diode out and loosen the connector of the bad aiming diode, tight this good aiming diode’s male connector with another female connector which inside of the scanner head. 3. Put the laser head at right focal distance, move this aiming diode and let two aiming diode’s… Seguir leyendo How to replace the aiming diode of Linxuan laser engraver?
How to Laser Print the Date and Time Automatically by EZCAD2?
With Linxuan laser engraver and the software EZCAD2, you can mark the date and time automatically. Here are the steps: 1. Click “Draw Text” tool, and choose “Enable variable Text”, then “Add” the “Date”, you can choose “Year-2020” or “Year-20” as you like to use, then click “OK” to add the year. 2. “Add”->”Date”->choose “Month”, then click “ok” to add the… Seguir leyendo How to Laser Print the Date and Time Automatically by EZCAD2?
How to set the laser mark curve text in EZCAD2?
1. Click “draw circle” tool, set diameter, and draw a circle. 2. Click “Draw text” tool, then move the mouse pointer to the circle line. 3. Press left mouse button. 4. Here can edit the text font, height as below. 5.Click “F”, it is better choose “align center”. 6. Click “T” , there are some… Seguir leyendo How to set the laser mark curve text in EZCAD2?
How to set the laser mark color in EZCAD2?
1. Open the EZCAD2 software, and import vector file such as for your logo or some others. 2. Change the size of the vector file you need. 3. Ungroup the vector file if you need to mark different color for different part of this vector file. 4. Choose one part you need. 5. Hatch it,… Seguir leyendo How to set the laser mark color in EZCAD2?
How to align the laser red frame in EZCAD2?
1. Click “Param(F3)”-> Other -> Red light pointer, as in the below picture: 2. Change the number in “Offset Pos X” and “Offset Pos Y” to adjust the red frame position, change the number in “Size ScaleX” and “Size ScaleY” to adjust the red frame size.
How to adjust the laser marking field in EZCAD2?
1. In EZCAD2, Click “Param(F3)” -> and click “Field” 2. Find Galvo 2 -> Scale, and click ” >>” 3. Such as we draw a 100mmx100mm frame in software, here we fill “100” in “Goal mark size”, measure the actual marking size in X axis, and fill the number in “Real mark size”, and click “OK” (Notice please: Galvo… Seguir leyendo How to adjust the laser marking field in EZCAD2?
