Follow the steps to set 3D Emboss Engraving of EZCAD3: 1. Enter 3D view, click “STL” to import a 3D file, or we can click “Creating a basic 3D surface” to create a basic 3D file. 2. We can view it from different directions. 3. Slice the 3D file. 4. Click “Add contour”, then click… Continue reading How to set 3D Emboss Engraving of EZCAD3?
FAQs: Laser Engraving Problems and Solutions
During laser engraving or marking business, it is inevitable to come across some embarrassing interludes. In this catalog, we’ve compiled a collection of common laser engraving problems and solution suggestions.
They include but are not limited to:
- Problems with laser machines installation, connections, main unit, or power supply.
- Questions about laser marking software, such as operation, functions, parameters, engraving file formats and other doubts.
- Concerns regarding the selection of engraving materials.
We hope these resources help you quickly resolve any issues you face while working with laser machines. If not, feel free to reach out to us for assistance – we’d be delighted to help!
How to set 2D Emboss Engraving of EZCAD3?
Follow the steps to set 2D Emboss Engraving of EZCAD3: 1. Create a new TEXT 2D file or import a vector file to Ezcad3, set its size and put it to center. 2. Click “3D” to enter 3D view, click “Slice” to slice the file, remember to tick “Using selected two-dimension object hierarchy”, set the… Continue reading How to set 2D Emboss Engraving of EZCAD3?
How to Adjust the Power of an Inno UV Laser Source?
The product of pulse width and frequency is approximately 1,000 (the actual value is around 960). For example, at 50 kHz, the maximum power corresponds to a pulse width of 19, while the minimum power corresponds to a pulse width of 1. Inno Laser sources have a frequency range of 30–150 kHz. However, to make… Continue reading How to Adjust the Power of an Inno UV Laser Source?
How do I reset the dimensions of the marking area frame in EZCAD2?
System parameter -> WorkSpace Left bottom corner: The X and Y values are both set to half of the field lens’s working range (e.g., 55, 55). Size: Set the Width and Height to the values of the field lens‘s working range (e.g., 110, 110).
How to Use a Linxuan UV Laser Marking Machine with a Water Chiller? A Step-by-Step Guide
This article primarily covers the operating procedures and precautions for the Linxuan UV laser marking machine and its associated water chiller. Water Chiller Installation 1. Add purified water to the chiller, and the water level over the part that marked in picture. 2. There are two lines, one connect power supply, another connect to the… Continue reading How to Use a Linxuan UV Laser Marking Machine with a Water Chiller? A Step-by-Step Guide
How to take off the control card of Linxuan laser engraver?
1. Take off the cabinet case with rotating the 10 screws on two sides. 2. Then you will see the control card on a metal sheet. Take off it with the two screws. And take of the plug on the card. Please be careful when do it. 3. Then take off the card.
How to take off the laser head of Linxuan laser engraver?
1. First, take off the lens with rotating the bottom piece in red circle. Please note not rotate the whole black part. But only rotate the bottom. Please hold the lens by another hand when rotating. So that it will not fall on the ground. Please take care of the lens to put it in… Continue reading How to take off the laser head of Linxuan laser engraver?
How to replace the aiming diode of Linxuan laser engraver?
1. Loosen these three screws. 2. Pull the aiming diode out and loosen the connector of the bad aiming diode, tight this good aiming diode’s male connector with another female connector which inside of the scanner head. 3. Put the laser head at right focal distance, move this aiming diode and let two aiming diode’s… Continue reading How to replace the aiming diode of Linxuan laser engraver?
How to Laser Print the Date and Time Automatically by EZCAD2?
With Linxuan laser engraver and the software EZCAD2, you can mark the date and time automatically. Here are the steps: 1. Click “Draw Text” tool, and choose “Enable variable Text”, then “Add” the “Date”, you can choose “Year-2020” or “Year-20” as you like to use, then click “OK” to add the year. 2. “Add”->”Date”->choose “Month”, then click “ok” to add the… Continue reading How to Laser Print the Date and Time Automatically by EZCAD2?
